5ХНМ / L6 / 1.2713 / 5CRNIMO
Characteristics for grade 5KHNM (5ХНМ) Grade:
Brand: |
5ХНМ |
Substitute: |
5ХНВ, 5ХГМ, 4ХМФС, 5ХНВС, 4Х5В2ФС |
Classification: |
Tool steel |
Products offered by advertisers: No data |
Application: |
hammer dies of steam-air and pneumatic hammers with a mass of falling parts over 3 tons, press dies and dies of machine high-speed stamping during hot deformation of light non-ferrous alloys, matrix blocks for inserts of horizontal forging machines. |
Chemical composition in% for grade 5ХНМ (5ХНМ)
GOST 5950-2000
C |
Si |
Mn |
Ni |
S |
P |
Cr |
Mo |
Cu |
0.5 - 0.6 |
0.1 - 0.4 |
0.5 - 0.8 |
1.4 - 1.8 |
up to 0.03 |
up to 0.03 |
0.5 - 0.8 |
0.15 - 0.3 |
up to 0.3 |
Temperature of critical points for grade 5ХНМ (5ХНМ)
Ac1 = 730 , Ac3(Acm) = 780 , Ar3(Arcm) = 640 , Ar1 = 610 , Mn = 230 |
Технологические свойства материала 5ХНМ
Свариваемость: |
не применяется для сварных конструкций. |
Флокеночувствительность: |
чувствительна. |
Склонность к отпускной хрупкости: |
не склонна. |
Механические свойства при Т=20oС материала 5ХНМ
Сортамент |
Размер |
Напр. |
sв |
sT |
d5 |
y |
KCU |
Термообр. |
- |
мм |
- |
МПа |
МПа |
% |
% |
кДж / м2 |
- |
Сталь |
100 - 200 |
|
1570 |
1420 |
9 |
35 |
340 |
Закалка 850oC, масло, Отпуск 460 - 520oC, |
Твердость 5ХНМ после отжига , ГОСТ 5950-2000 |
HB 10 -1 = 241 МПа |
Физические свойства материала 5ХНМ
T |
E 10- 5 |
a 10 6 |
l |
r |
C |
R 10 9 |
Град |
МПа |
1/Град |
Вт/(м·град) |
кг/м3 |
Дж/(кг·град) |
Ом·м |
20 |
|
|
|
|
|
|
100 |
|
|
38 |
|
|
300 |
200 |
|
12.6 |
40 |
|
|
250 |
300 |
|
|
42 |
|
|
200 |
400 |
|
|
42 |
|
|
160 |
500 |
|
|
44 |
|
|
|
600 |
|
14.2 |
46 |
|
|
|
T |
E 10- 5 |
a 10 6 |
l |
r |
C |
R 10 9 |
Зарубежные аналоги материала 5ХНМ
Внимание! Указаны как точные, так и ближайшие аналоги.
США |
Германия |
Япония |
Франция |
Англия |
Евросоюз |
Италия |
Испания |
- |
DIN,WNr |
JIS |
AFNOR |
BS |
EN |
UNI |
UNE |
L6 T61206 |
1.2711 1.2713 55NiCrMoV5 55NiCrMoV6 56CrNiMoV7 G55NiCrMoV6 |
SKT3 SKT4 |
55NCDV7 55NiCrMoV7 |
BH224/5 |
1.2714 55NiCrMoV7 |
44NiCrMoV7KU 55NiCrMoV7KU |
F.520S |
Китай |
Швеция |
Болгария |
Венгрия |
Польша |
Румыния |
Чехия |
Австрия |
Юж.Корея |
GB |
SS |
BDS |
MSZ |
PN |
STAS |
CSN |
ONORM |
KS |
5CrNiMo |
2550 |
5ChNM |
NK |
WNL WNL1 |
55MoCrNi16 55VMoCrNi16 |
19662 |
W502 |
STF4 |
Обозначения:
Механические свойства : |
sв |
- Предел кратковременной прочности , [МПа] |
sT |
- Предел пропорциональности (предел текучести для остаточной деформации), [МПа] |
d5 |
- Относительное удлинение при разрыве , [ % ] |
y |
- Относительное сужение , [ % ] |
KCU |
- Ударная вязкость , [ кДж / м2] |
HB |
- Твердость по Бринеллю , [МПа] |
Physical properties: |
T |
- Temperature at which these properties are obtained, [Grad] |
E |
- Modulus of elasticity of the first kind, [MPa] |
a |
- Coefficient of thermal (linear) expansion (range 20o - T), [1 / Grad] |
l |
- Coefficient of thermal conductivity (heat capacity of the material), [W / (m · deg)] |
r |
- Density of the material, [kg / m3] |
C |
- Specific heat capacity of the material (range 20o - T), [J / (kg · deg)] |
R |
- Specific electrical resistance, [Ohm · m] |
Weldability: |
without Borders |
- welding is carried out without heating and without subsequent heat treatment |
limited weldable |
- welding is possible when heated to 100-120 degrees. and subsequent heat treatment |
difficult to weld |
- to obtain high-quality welded joints, additional operations are required: heating up to 200-300 degrees. when welding, heat treatment after welding - annealing |